Epson SureColor F7170 Průvodce nastavením

Epson® SureColor® F7170 Setup Guide

10 | Installing the PrinterMake sure you have the following items before installing the printer.1. Lock the casters and fix the stand in place. To fix

Installing the Printer | 112.From the front of the printer, insert the carry bars into both sides of the printer with the locking bolts toward the gro

12 | Installing the Printer4. Lift the printer onto the stand. Line up the marks on the bottom of the printer with the arrows on the top of the stand’

Installing the Printer | 137.Open the front cover and remove the tape.8. Remove the media holding plates.9. Feed the long waste ink tube through the h

14 | Installing the Printer10. Open the clips.11. Slide the waste ink tube into its bracket and close the clips. Gently pull up on the tube to tighten

Installing the Printer | 1513.Slide the ink splash guard onto the waste ink tube.14. Install the waste ink tank into the bracket. Make sure the waste

16 | Installing the Media Feeding UnitInstalling the Media Feeding UnitYou need the following parts to assemble and attach the media feeding unit:Note

Installing the Media Feeding Unit | 172.Lower the media feeding unit onto the brackets.3. Attach the media feeding unit to the stand using five C scre

18 | Installing the Media Feeding Unit5. Run the communication cable through the cable supports.6. Lift the port cover.7. Plug in the communication ca

Installing the Take-up Reel System | 198.Make sure the communication cable is fully seated in the port and then close the port cover.Installing the Ta

2 |ContentsUnpacking the Printer ...

20 | Installing the Take-up Reel SystemCaution: Use at least two people to lift the take-up reel. To avoid damaging the take-up reel, lift it by holdi

Installing the Take-up Reel System | 214.Attach the take-up reel to the stand using four C screws.Note: Leave the screws loose until the service engin

22 | Installing the Media Guide BarInstalling the Media Guide BarYou need the following parts to assemble and attach the media feeding unit:1. Place t

Installing the Media Guide Bar | 232.Attach two screws to the media guide mounting bracket.3. Attach a screw to the media guide mounting bracket.2Ea1

24 | Installing the Media Guide Bar4. Loosely attach two screws to the stand.5. Place the bracket over the screws, shift the bracket to the left, then

Connecting to a Power Source | 257.Attach the other side of the media guide bar using two screws.8. Contact a service engineer to attach the Ink Suppl

26 | Setting the Language2. Thread the power cords through the cable supports. Connect the power cord to the printer and use the cable supports to res

Loading Media | 27Loading Media1. Press the P power button to turn on the printer.2. Open the front cover and then raise the media loading lever.

28 | Loading Media3. Loosen the screws on the roll holders and slide the roll holders towards the outside of the printer.4. Align the left end of the

Loading Media | 295.Using two or more people, move the media onto the roll holder, adjusting the roll holder as necessary. When the media is securely

Unpacking the Printer | 3Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the

30 | Loading Media7. Pull up the roll holder lever, slide the roll holder into the media roll.8. Push the roll holder towards the center of the roll,

Loading Media | 319.Turn the roll holder handle clockwise until part A is hidden. When part A is hidden, do not turn the handle any further.10. Pull t

32 | Loading Media11. Lower the media loading lever.12. Raise the media loading lever and then pull the media through the front of the printer.13. Pul

Loading Media | 3314.Close the front cover.15. After loading the media, you will be prompted to choose setup and media options. Choose options as nece

34 | Loading Media17. Open the front cover.18. Attach the media holding plates while aligning their positions. The media holding plates should be inst

Installing the Software | 3519.Close the front cover.Installing the SoftwareInsert the software CD that came with your printer into your computer and

36 | USB InstallationUSB Installation1. Press the P power button to turn off the printer, then connect the USB cable to the printer and your computer.

Network Installation | 37Network Installation1. Press the P power button to turn on the printer, if necessary.2. Connect the Ethernet cable to the pri

38 | Network Installation4. Follow the on-screen instructions to complete the installation, keeping the following points in mind:• Do not remove the c

4 | Unpacking the PrinterWhen choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct

Unpacking the Printer | 5Media System AssemblyThe item below can be found in the “Ink Supply System Cover 1” box.b265 E4F2G2DMedia feeding unitTake-up

6 | Assembling the StandAssembling the StandMake sure you have the following items before assembling the stand.1. Remove the tape from the larger hori

Assembling the Stand | 73.Attach the smaller horizontal strut by securing two B screws (four total) in the back of the legs.4. Attach the waste ink ta

8 | Assembling the Stand6. Temporarily fasten the waste ink tube bracket using one B screw.7. Remove the four screws from each leg, then remove the pl

Installing the Printer | 99.Slide the mounting pieces into the grooves, as shown.10. Replace the plastic pieces and tighten all eight screws.Installin