Epson 22-681 Uživatelský manuál

INSTRUCTION MANUALDC-380 15" Planer(Model 22-680, Single Phase)(Model 22-681, Three Phase)PART NO. 1346996 - 07-30-04Copyright © 2004 Delta Mach

10ASSEMBLING SWITCH TO PLANER (THREE PHASE MACHINE ONLY)The switch for the three phase 15² Planer is supplied wired to the motor and is to be fastened

11ASSEMBLING TOP COVER ANDDUST CHUTE1. Fasten the top cover and dust chute (A) Fig. 16, to the top of the planer, as shown, using the three M6x16mm sc

12OPERATIONAL CONTROLS AND ADJUSTMENTSFig. 18ABLOCKING SWITCH IN THE “OFF”POSITIONIMPORTANT: When the machine is not in use, the switchshould be locke

13DEPTH OF CUT ADJUSTMENTThe depth of cut on your planer is controlled by raisingor lowering the head assembly (A) Fig. 22, whichcontains the cutterhe

14ANTI-KICKBACK FINGERSWHEN INSPECTING AND CLEANINGTHE ANTI-KICKBACK FINGERS, MAKE SURE THEMACHINE IS DISCONNECTED FROM THE POWERSOURCE.A series of an

15Fig. 30Fig. 31Fig. 32CHECKING, ADJUSTING ANDREPLACING KNIVESTo check, adjust or replace the knives, proceed asfollows:DISCONNECT MACHINE FROM POWERS

16Fig. 34 Fig. 35Fig. 36Fig. 375. If the knives are removed for sharpening, care mustbe exercised in replacing and resetting them, as follows:A. Remov

17ADJUSTING HEIGHTOF CHIPBREAKERThe chipbreaker extends down around the front of thecutterhead and raises as stock is fed through the planer.The chipb

18ADJUSTING HEIGHTOF INFEED ROLLERThe infeed roller is adjusted at the factory at 0.040"below the cutting circle. To check and adjust theheight o

19ADJUSTING SPRING TENSION OFINFEED AND OUTFEED ROLLERSThe infeed and outfeed rollers are those parts of yourplaner that feed the stock while it is be

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20ADJUSTING CUTTINGHEADPARALLEL TO TABLEThe cuttinghead is set parallel to the table at the factoryand no further adjustment should be necessary. If y

21When using your machine, you may want to follow these few simple steps for achieving the best results possible.1. True Up One Face – Feed one face o

22MAINTENANCEFig. 53Fig. 54ABFig. 55ECDFig. 56FLUBRICATIONThe gear box oil should be changed once a year. Useextreme pressure gear oil, available from

23PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5ADDITIONAL SAFETY RULES FOR PLANERSFAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURYSAVE THESE INSTRUCTIONS. Refer to them often an

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7EXTENSION CORDSUse proper extension cords. Make sureyour extension cord is in good condition and is a 3-wireextension cord which has a 3-prong ground

8UNPACKING AND CLEANINGCarefully unpack the machine and all loose items fromthe shipping container(s). Remove the protective coatingfrom all unpainte

9ASSEMBLYCUTTINGHEAD RAISING ANDLOWERING HANDWHEEL1. Insert key (A) Fig. 7, into keyway (B) of raising and lowering shaft.Fig. 7Fig. 82. Assemble hand