Epson EMP 600 Uživatelská příručka stáhnout pdf (Strana 39)

Turning On the Power and Projecting Images

Procedure

Turn on the power for all equipment connected to the projector.

For a video source, press the [Play] button at the video source to start

playback if necessary.

Check that the operation indicator

has stopped flashing and lights

orange.

If using the remote control, set the

R/C switch on the remote control to

the ON position.

Press the [Power] button on either

the remote control or the

projector's control panel to turn on

the power for the projector.

The operation indicator flashes green, and

after a short period projection starts.

Depending on the settings, the message

"No-Signal." may appear. (P.70)

Check that the operation indicator

has stopped flashing and lights

green.

Tip :

The projector buttons cannot be operated while the

operation indicator is flashing green. Wait until it

lights steadily.

Operation indicator lights orange

Power

A/V Mute

Freeze

E-Zoom

Power

Sync+

Tracking - Tracking +

Menu Esc

Help

Computer/YCbCr

Video

Source

Projector

Remote control

Operation indicator stops

flashing and lights green

Downloaded From projector-manual.com

If the projector cannot be set up so that it is perpendicular to the screen, you can

use the keystone correction function which is described on the following page

to adjust the projected images if the angle of the projector is within a range of

approximately 30° vertically or approximately 10° horizontally from the

perpendicular.

The values given here are for when the image is at the smallest zoom setting

(telephoto). The maximum angles will be smaller if the zoom setting has been

increased in the wide angle direction. Furthermore, if the projector has been

tilted both vertically and horizontally, the maximum adjustable angle will again

be smaller than the maximum angle if the projector had been tilted in only one

direction.

When tilted vertically

When tilted horizontally

30°

Approx. 30° above Approx. 30° below

10°

Approx. 10° to the leftApprox. 10° to the right

Downloaded From projector-manual.com

Tip :

• When keystone correction is carried out, the projected image will become smaller.

• Procedure to follow if using both horizontal and vertical keystone correction:

1. With the front adjustable foot retracted, set the projector so that it is fully horizontal.

2. Extend the front adjustable foot to adjust the angle as necessary.

3. Adjust the vertical keystone distortion until both sides of the picture are vertical.

4. Adjust the horizontal keystone distortion until the top and bottom edges of the

picture are both horizontal.

• The keystone correction settings are memorized, so that if you change the position or

angle of the projector, you may need to readjust the keystone correction settings.

To return a previous keystone correction to the initial setting, carry out the following

operations.

To initalize vertical keystone correction: While holding down the [Sync +] button,

press the [Sync -] button for 1 second or more.

To initalize horizontal keystone correction: While holding down the [Tracking +]

button, press the [Tracking -] button for 1 second or more.

• If the images become uneven in appearance after keystone correction is carried out,

decrease the Sharpness setting. (P.63)

• Keystone correction can also be carried out using the projector menu. (P.69)

• If you carry out both horizontal and vertical keystone correction, the correction range

will become smaller than it would be if only one type of correction was carried out.

• If the value displayed in the gauge on the screen stops changing when horizontal or

vertical keystone correction is being carried out, it indicates that the limit for

horizontal or vertical keystone correction has been exceeded. Check that the projector

has not been set up at an angle which exceeds the proper limit.

• If either the E-Zoom, Effects or P in P functions are used at the same time as horizontal

or vertical keystone correction has been carried out, a message may appear on the

screen if these functions are used when the keystone correction amount is near the

limit. It may not be possible to use the E-Zoom, Effects or P in P functions if this

happens. In such cases, re-adjust the projector position so that the amount of keystone

correction required is reduced.

• The limit value for keystone correction will vary depending on the video signal being

input.

Downloaded From projector-manual.com

Tip :

• The [Auto] button on the projector's control panel does not work while a menu or help

screen is being displayed. To use the [Auto] button on the projector's control panel,

you need to first exit the menu or help screen. Alternatively, you can use the [Auto]

button on the remote control instead.

• If you use the remote control to activate the automatic adjustment function while the E-

Zoom, A/V Mute or Picture in Picture functions are in use, the functions being used

will be canceled before automatic adjustment is carried out. If the [Auto] button on the

projector’s control panel is pressed, automatic adjustment will not be carried out if the

E-Zoom or Picture in Picture function is being used.

• Automatic adjustment may not work properly with some types of signals which are

output by computers. In such cases, you may need to adjust the tracking and

synchronization manually.

If vertical stripes appear in the projected images,

and this cannot be fixed using automatic

adjustment. You will need to adjust the tracking

manually using the following procedure.

Procedure

While holding down the [Shift] button

on the projector's control panel, press

the [Tracking +] button.

The tracking value will increase by one setting

each time the [Tracking +] button is pressed.

[While holding down the [Shift] button

on the projector's control panel, press

the [Tracking -] button.

The tracking value will decrease by one setting

each time the [Tracking -] button is pressed.

Tip :

The image will flash when continuous tracking

adjustment is carried out, but this is normal.

Adjusting the tracking

Resi e

Sync+

Tracking - Tracking +

Sync-

Keystone

Shift

Auto

Projector

Sync+

Tracking - Tracking +

Sync-

Keystone

Shift

Auto

Projector

Downloaded From projector-manual.com

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 117 118

Komentáře k této Příručce

Žádné komentáře

Epson EMP 600 Uživatelská příručka Strana 39

Komentáře k této Příručce

Související produkty a manuály pro Datové projektory Epson EMP 600