Epson 1010 Uživatelský manuál stáhnout pdf

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code

www.soc-machines.com

- 1 -

Epson E1007 Description

The Epson E1007 is a 4x12 Monochrome LCD almost identical in operation to the ECM-A1010

display – controller is Epson SED1230 chip. The E1007 has a serial interface while the E1010

uses an 8bit parallel interface. The E1007 is illuminated by four LEDs wired in series (I think)

while the E1010 has two. A complete technical description and programming guide for the

SED1230 chip is provided in the Epson SED1200 Series Technical User Guide (see the Epson

Electronics web site). The E1007 pin out is on the left while the E1010 is on the right. The

E1010 has symbols on the top row and left column while the E1007 has fewer top row symbols

and no left column symbols. Symbol display control commands differ between the two displays.

The spec sheet states that the display will operate from 2.4 to 3.6V – this we found to be true –

this is not a 2.8V only display but runs fine from 2.4 to 3.6V.

E1007 Pin Assignment

E1010 pin assignment

The picture below shows the pin locations described in the table above.

Pin Symbol

I/O Description

1 LED+ I LED Anode

2 LED- I LED Cathode

3 A0 I

Selects Register

(L-Command, H-Date)

4 CS I Chip Select (L-Enable)

5 SI I Serial Data

6 SCL I Serial Clock

7 VDD I

Power supply for logic

(2.4V-3.6V)

8 GND I Ground

9 NC No Connection

10 NC No Connection

11 GND2 I Ground 2

12 VDD2 I

Power supply2 for logic

(2.4V-3.6V)

13 RES I Reset

1 2 3 4 5 6 7

Shrnutí obsahu

Strany 1

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 1 - Epson E1007 Description The Epson E1007 is a 4x12 Monochr

Strany 2

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 2 - The E1007 display is shown above. The Vol

Strany 3

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 3 - Mapping of symbol register to symbol addre

Strany 4

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 4 - Example C code to program E1007 – note this is a code sn

Strany 5

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 5 - // D3-N2, D2-N1, D0-CG // N2/1 -> 0,0 2 lines //

Strany 6

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 6 - void LCDDisplayChar(unsigned char address, unsigned ch

Strany 7

Epson E1007 4x12 LCD Display Connector Pin Out and Start-up Code www.soc-machines.com - 7 - // VF -> 1 voltage follower on, 0 off //

Komentáře k této Příručce

Žádné komentáře

Epson 1010 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Tisk a skenování Epson 1010. Epson E1007 Pinout Brief Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Tisk a skenování Epson 1010